Featured Products
Maximize Energy Harvest and Improve Battery Life
The PT-100 is a Maximum Power Point Tracker (MPPT) charge controller designed to harvest the maximum available energy from the PV array and deliver it to the batteries. The PT-100’s MPPT algorithm finds the maximum power point of the array and operates at this point while regulating the output current and battery voltage to fully charge the battery.
Features
High Efficiency: The PT-100 provides higher than 99% conversion efficiency and uses less than two watts of power in nighttime mode.
MPPT: Maximum Power Point Tracking technology for increased PV power output efficiency.
Voltage Options: Compatible with 12, 24, or 48V battery systems with automatic detection of system voltage. The PT-100 will produce up to 100 amps regardless of battery voltage.
Supports a Large PV Array: A single controller supports a large PV array up to 6600W. Larger PV arrays may be used because the PT-100 is current limited to 100 amps for maximum harvest.
Optimal Battery Charging: Automatic battery temperature compensation using an included external temperature sensor for optimum battery charging, even during extreme temperature changes.
Multi-stage Charging: Maximizes system performance and improves battery life.
GFDI: Integrated PV GroundFault Detection and Interruption/ Indication, with pre-fault leakage/ diagnostic metering.
LED Indicators and Screen: Multiple LED indicators and large digital LED screen on front panel for easy-to-read system information.
On-site Updates: The PT-100’s software can be updated on site.
Extensive Electronic Protection: Over-temperature protection, power derating when temperature is high, PV short circuit and high PV input shutdown, output overcurrent protection and night-time back-feed (reverse current) protection.
AFCI: An integrated PV ArcFault Circuit Interrupter detects, indicates, and extinguishes series arcs. The AFCI is designed to meet the new National Electric Code (NEC) Article 690.11 requirements.
Convenient Installation: Run all of the wiring to the unique, remain-inplace wiring box with ease prior to installing the full PT-100 unit.
Easy MP and MMP integration: The PT-100 is designed to work with a Magnum Panel (MP) or MiniMagnum Panel (MMP). It provides room and access to PV and battery disconnect breakers.
Even More Functionality with the Optional Remote
Built-in programmable auxiliary relay for device control.
Internal data logging functionality keeps energy harvest information and battery Ahr/Whr data up to 255 days.
Use the optional remote to display this information.
The MMP – Mini Magnum Panel is an inclusive, easy-to-install panel designed to work with one Magnum MS-AE, MS-PAE, MS, RD or other non-Magnum inverter / charger.
***Inverter sold seperately***
Small Footprint
only 12.5″ wide x 18″ tall x 8″ deep
Easy Access
front-mounted breakers and remote (optional)
Choices
can be wired for 120 VAC or 120/240 VAC output
Inclusive
works with non-Magnum inverter / chargers (may require the optional knockout plate for the top of the MMP: an MMP-KP)
Regulatory Markings
ETL listed to UL1741 and CSA C22.2 107-01
DC Load Breakers
fits either din rail or back-mount DC load breakers.
Included
One DC breaker – 175A or 250A
One AC bypass breaker – 30A dual pole or 60A single pole
One AC input breaker – 30A dual pole or 60A single pole
500A/50mv DC shunt
DC buss bars for battery positive and negative
Din rail or back mount for optional DC mini breakers – will hold up to eight breakers
Inverter hood
The MPSL – Magnum Panel, Single Enclosure, Low Capacity – is designed to accommodate a maximum of two inverters.
***Inverters sold separately***
Features
Expandable:
start with the enclosure and just one inverter and in the future expand to two inverters with ease, using the MPX.
Easy installation:
all connections are frontmounted, including AC and DC breakers and the MPX.
DC load breakers:
fits either din rail or back-mount DC load breakers.
Convenient knockouts:
knockouts on the side of the enclosure are compatible with most charge controllers.
Included
One DC breaker – 175A or 250A
One 60A AC bypass breaker
500A/50mv DC shunt
Inverter AC input protection
Inverter hood
The MPSH – Magnum Panel, Single Enclosure, High Capacity – is designed to accommodate a maximum of three inverters.
***Inverters sold separately***
Features
More power capacity:
the 125A bypass breaker and the 1000A DC shunt safely handle the power from larger systems.
Expandable:
start with the enclosure and just one inverter and in the future expand to up to three inverters with ease, using the MPX.
Easy installation:
all connections are frontmounted, including AC and DC breakers and the MPX.
Convenient knockouts:
knockouts on the side of the enclosure are compatible with charge controllers.
Includes
One DC breaker – 175A or 250A
One 125A AC bypass breaker
1000A/100mv DC shunt
Inverter AC input protection
Inverter hood
The MPDH – Magnum Panel, Dual Enclosure, High Capacity – is designed to accommodate a maximum of four inverters with two enclosures – one for AC connections and one for DC connections.
***Inverters sold separately***
Features
More power capacity:
the 125A bypass breaker and the 1000A DC shunt safely handle the power from larger systems.
Expandable:
start with the enclosures and just two inverters and in the future expand to up to four inverters, using the MPX.
Easy installation:
all connections are frontmounted, including AC and DC breakers and the MPX.
Labor saving:
panel is pre- wired for fast installation, saving labor costs.
DC load breakers:
fits either din rail or back-mount DC load breakers.
Separate AC and DC enclosures:
for installers who prefer separate enclosures, the MPDH provides an easy solution.
Includes
Two DC breakers – 175A or 250A
One 125A AC bypass breaker
1000A/100mv DC shunt
Inverter AC input protection
Two inverter hoods
